Instagram story viewer> @privateissues.wrld> Post

Private Issues

@privateissues.wrld

3 months ago

269

1

Posted On: June 25th 2026, 02:43 pm

ᴍᴏᴅᴇʀɴ ᴀʀᴍᴏʀ ꜰᴏʀ ᴛʜᴇ ꜱᴛᴀɢᴇ.
@nerdesinpango ɪɴ ᴛʜᴇ ᴋɴɪɢʜᴛ ᴢɪᴘ-ᴜᴘ.

ᴡᴡᴡ.ᴘʀɪᴠᴀᴛᴇɪꜱꜱᴜᴇꜱ.ᴄᴏᴍ

Comments (1)

morvymaven

3 months ago

morvymaven

😍

More posts

Lace, shadows, and a little attitude. ✨ Confidence is always the finishing touch. #EditorialStyle #AfterDarkGlam

Welcome to Episode 02 of Agent Wars. Today we’re challenging 5 top AI models to design, engineer and 3D print a bridge with the goal of holding the most possible weight.

For Episode 02, here are the models I tested, with their reasoning level and the harness I used for each:
 🇺🇸 Anthropic: Claude Opus 5.5 (High)
🇨🇳 Kimi: Kimi K3 (High)
🇺🇸 Meta: Muse Spark 1.3 (High) 🇺🇸 OpenAI: GPT 6 Astra (High) 🇺🇸 SpaceXAI: Grok 4.7 (High)

Each bridge had specific parameters. It had to span 2 feet, use a maximum 500 grams of filament, and it had to be under 18 hours of printing time. We specified what type of weight and where we would place it on the bridge.

🏆 THE SCORE:

Claude Opus 5.5 held an estimated 130 lbs! It took 9 hours and 11 minutes to print 17 parts and used 441 grams of filament.

Meta Muse Spark 1.3 held 26.5 lbs. It took 13 hours and 12 minutes to print 49 parts and used 478 grams of filament.

OpenAI GPT-6 Astra held an estimated 17.5 lbs. It took 15 hours and 44 minutes to print 29 parts and used 442 grams of filament.

SpaceXAI Grok 4.7 did not finish. On assembly it could not stand up by itself. It took 12 hours and 22 minutes to print 29 parts and used 460 grams of filament.

Kimi K3 did not finish. It wasn’t engineered correctly so the bridge could not even be assembled. It took 11 hours and 19 minutes to print 35 parts and used 446 grams of filament.

🏅 That means our champion for this episode is Claude Opus 5.5. Not only did it hold the most weight (by FAR) it also took the least time to print, used the least amount of parts and used the least amount of filament.

Getting ready to celebrate little Aoileann’s Christening yesterday and our upcoming 10 year wedding anniversary this week ☺️✨🙏🏻

Dress and Jacket: @beowell.ie (dress is sadly a sample but the jacket is available now)
Earrings: @beowell.ie
Bag: My wedding bag 🥹 @manleystudio
Shoes: Old mango as my wedding shoes now two sizes too small for me (kids will do that to you 😂)
Make Up: @l.lafferty_makeup_beauty

Sam and Teigan… No notes. ❤️💙

Selama ini kita mungkin lebih sering memperhatikan kemegahan Masjidil Haram dan Masjid Nabawi dari lantai atau bagian luarnya. Padahal, langit-langit di dalamnya juga memiliki detail arsitektur yang begitu indah.

Tak hanya Masjidil Haram dan Masjid Nabawi, Masjid Quba dan Masjid Al-Ghamamah di Madinah juga memiliki desain langit-langit dengan karakter yang khas. Ornamen, pola, hingga permainan bentuk pada bagian plafonnya membuat suasana di dalam masjid terasa semakin menawan.

Keindahan tersebut menjadi pengingat bahwa masjid-masjid di Tanah Suci bukan hanya memiliki nilai sejarah dan spiritual, tetapi juga menyimpan kekayaan arsitektur yang menakjubkan.

Semoga kita semua suatu hari diberi rezeki untuk melihatnya secara langsung. Inilah alasan kami mau jadi kaya raya ya Allah 😭🤲

#taubatters

My silly silly dump