Instagram story viewer> @vtecinnovations> Posts

VTEC Innovations

@vtecinnovations

490

followers

104

following

Built for racers. Powered by passion.
Honda swap kings — K, D, EG, EK, B-series.
Race-spec. Mil-spec. No shortcuts.
USA made. Snake Tuning partner.

POSTS STORIES REELS TAGGED

Link Razor PDM build, fully sealed and epoxy-filled. Labeled power and ground leads, sealed connections, and a clean layout throughout.

This one is being paired with a full custom VTI Link G5 Voodoo harness for a big-turbo B-series build.
This PDM will directly control all high power modules included 3 fans and a large fuel pump.

#wiredbyVTI #motorsport #autosport #customproduction #linkpdm @link_ecu @phastuning by @vtecinnovations

167

4

10 days ago

Custom OEM-replica harness for a drive-by-wire AP2 S2000. Built as a complete plug-and-play replacement using mil-spec wire and materials, with high-heat braided sleeving in Spoon Sports-inspired blue.

The customer started a DIY reloom and sent us their color references. We built a new harness around the factory layout to bring their idea together. Photos include the original harness they brought us and the replacement.

Thanks to @phastuning for helping behind the scenes. We’re also working together on drop-in harness and ECU packages designed to get customers plugged in and driving the same day.

#wiredbyVTI #motorsportwiring #autosport #PHASTUNED by @vtecinnovations

18

3

12 days ago

11 relays. 20 fuses. One K-swapped EF getting the full VTI treatment. ⚡️

Just wrapped up this custom relay/fuse assembly, built to bring a FuelTech FT450, Nano wideband controller and our full engine harness together in a stripped EF chassis.

Main power, ignition, starter, coils/injectors, VTEC, fuel pump and cooling fan—all handled here. Chassis duties covered too: horn, high/low beams, park/tail lights, brake lights, turn signals and reverse lights.

Factory buttons and switches stay in use, with A/C and radio AUX outputs included. Stripping the chassis doesn’t mean giving up the functions you actually want.

Sealed connector breakouts, labeled branches and accessible relays and fuses keep installation and future service straightforward. Engine management and chassis wiring planned together from the start.

Built in-house. Built for this car. VTI Motorsports.

#VTIMotorsports #FuelTech #FT450 #EFCivic #KSwap #MotorsportWiring by @vtecinnovations

15

2

a day ago

Our “BMF” relay kits now have their own spot in the VTI Project Builder.😉

TE high-current relays, bolted stud-and-lug power connections, fused battery feeds, and a separate disconnectable trigger harness. Built to your pump or fan, cable routing, and control setup.

Shown is a custom 10AWG setup for a 525 pump, wired through a two-wire bulkhead pass-through directly to the pump connector. Clean routing, proper protection, and serviceable connections—the details we put into our larger harnesses, carried into a dedicated power kit.

Builds start at $199. Send us your setup through the builder and we’ll work out the specification and quote before payment. Photos are a completed custom build for reference; yours gets built around what you need.

https://build.vtecinnovations.com/configure?kit=fuel-pump-fan-relay

#VTIMotorsports #CustomHarness #MotorsportWiring by @vtecinnovations

18

0

4 days ago

Engine harnesses. ECU packages. PDM wiring. Custom adapters.

Our VTI Project Builder is open for testing. Choose your project, select your equipment and send us the details for review and quoting.

Built by VTI. Spec’d for your project.

build.vtecinnovations.com by @vtecinnovations

10

0

8 days ago

Following our Link PDM post, here’s a look at how we handle dedicated fuel-pump power with a CONVENTIAL relay setup.

No CAN bus required. Factory or standalone ECU control, with a dedicated power feed bypassing the original pump wiring.

Shown is a TE relay rated for 70A+ continuous duty, with power terminals accommodating up to 4 AWG.

This assembly features:

• 10 AWG M22759/16 wire
• Tight-fitting 3/16” DR-25 protection
• SCL-sealed ends
• Standard VTI yellow identification labels
• Two-pin connector for the relay trigger circuit
•30-50a inline battery fuse protection

The focus is low resistance, minimal voltage drop, and reliable switching under load. Wire sizing, terminations, and protection all matter just as much as the relay itself.

We’ve run dual Hellcat pumps on a single one of these 70A relays with current headroom in that setup. Each application gets sized around its actual current demand, startup load, and duty cycle.

Built in-house at VTI Motorsports.
#wiredbyvti #motorsportNOTmilspec #phastuning #oxytuned #racespec by @vtecinnovations

17

0

9 days ago

H2B, H22/23, F20b, F23, B20, B18, B16, D16/15.

You see it above, it fits.

VTI Motorsport In-House H/B-Series loom is now live on site.
Covering a majority of OBD1 ecu platforms, these purpose built and designed Motorsport looms are for those looking to step above the off-the-shelf and common “universal” “tucked” harnesses.

True full length MIL wire, ZERO splices, color ident marked, and completely twisted to near perfection. With simple plug and play set up, and additional seamless options, these are a one-and-done unit.

Live now-www.vtecinnovations.com
#wirebyvti #motorsportwiring #hondaloom by @vtecinnovations

19

2

22 days ago

Busy, busy, busy, I guess that’s our moto over here at VTI recently. Lots of good, clean, planned builds being produced behind the scenes as always.

We are looking to bring in some part-time help with social media managing, footage posting and organizing, overall media exposure.

Currently VTI is solely owned, operated, managed, and labored by one human. It’s a lot to do and handle considering our current standing, and I feel you guys deserve more frequent views of behind-the-scenes and product shots to keep things real.

Shoot us a DM if this is something you have good prior experience and success with and we can make something happen!

In the meantime I’ll try to get some more time set aside to show off some current projects and builds!

Ft450-K24 swap partials:⬇️📸

#wiredbyvti #motorsportwiring #handbuilt by @vtecinnovations

9

1

23 days ago

Polished💎

Final Friday bench-shots of the LINK ecu OBD2A Motorsport Loom.
Pure hand-crafted quality.

Looking for something PURPOSE built?
Get yours #wiredbyVTI
👉🏼 https://www.vtecinnovations.com/pages/custom-engine-harness-inquiry by @vtecinnovations

11

0

2 months ago

Del sol project is nearing completion and first start is around the corner!! Many thanks to @vtecinnovations for all the help along the way. Fantastic work by @oxytuned on the ECU and many thanks to all who supported the process. #honda #hondatuning #d16z6 #d16z6turbo #turbo taken in Morrisville, Vermont by @vtecinnovations

23

7

2 months ago

Just about wrapped up on this full scale LINK ecu PNP OBD2B loom.
Complete with:

Bosche Combo Sensor
AEM Oil Pressure Sensor
Direct fire k20 Coil Packs
Honed Development k20 style trigger kit
DTM2p Boost Control
CanBus Wideband
Custom Bulkhead charge cables
Full BLACK DTM Booted connectors where applicable
Custom routed to lay CLEANLY along frame rails
Fully populated to OEM Ecu plugs to bypass previous “expansion” loom usage

#clean #proficient #purposebuilt #WireByVTI by @vtecinnovations

14

0

2 months ago

Another quick one☝🏽
Quick Expansion loom for @cesar’s FT550 to K-Series adapter harness.

Opted for FULL DBW control with Honda APPS to cable,
J37 E-Throttle
And and additional A/C break out.

#wiredbyvti by @vtecinnovations

9

0

2 months ago